Hawk-industries Hawkjaw Sr. Manual 100K-2GSR Serial Numbers 101 to Manuel d'utilisateur Page 26
- Page / 165
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Operation26
Adjust for Break Out
Adjusting the Spinner
QR
1. Loosen the four spinner slide assembly bolts
(SAB).
2. Re-adjust the spinner slide assembly (SSA) forward
so that the push cylinder strokes out far enough to
reach the connection.
3. Tighten the spinner slide assembly bolts (SAB).
Spinner performance could be reduced if the
spinner push cylinder stroke is insufficient to
allign the spinner correctly with the drill pipe,
especially on sizes above 5 1/2" tube. To correct
this problem:
NOTE
D
SAB
SSA
I
1. Measure the drill pipe tube with
OD calipers.
2. Remove the quick release pins
(QR).
3. Slide the whole Drive unit (D)
forward or backward to the
appropriate holes. Use the pipe
size index (I) to adjust the drive
unit to the correct setting.
4. Replace the quick release pins
(QR).
- OPERATION, MAINTENANCE 1
- SERVICE MANUAL 1
- MODEL 100K-2GSR 1
- Introduction 2
- Table of Contents 3
- Warranty 6
- Specification Sheet 7
- Ordering Instructions 8
- Hanging Cable Location 9
- HawkJaw Location 9
- Hanging Cable Requirements 10
- Hydraulic Requirements 11
- Air Requirements 12
- Installation 13
- Winch Hook - Up 14
- Start-up Procedure 17
- Adjust for Make Up 18
- Position for Make Up 20
- Position for Make Up (cont.) 21
- Setting Make Up Torque 22
- Operation 23
- Low Torque Warning Test 24
- Adjust for Break Out 25
- Position for Break Out 27
- Break Out 29
- Wrench Maintenance 30
- Filter Maintenance 34
- Changing the Hook Dies 36
- Changing the Heel Dies 37
- Spinner Maintenance 43
- Changing the Spinner Chain 48
- Changing the Drive Rollers 50
- Drive Roller Sprocket Bear 52
- Maintenance 53
- & Repair 53
- Changing the Torque Cylinder 54
- Changing the Grip Cylinders 58
- Main Block Fittings and 64
- Air Logic System and Main 65
- Changing All Other 66
- HawkJaw Parts 66
- Trouble Shooting 67
- Troubleshooting 77 77
- 78 Drawings 78
- Drawings 79 79
- 80 Drawings 80
- Drawings 81 81
- 82 Drawings 82
- Drawings 83 83
- 84 Drawings 84
- Drawings 85 85
- 100K-2GSR HangerAssembly 86
- 88 Drawings 88
- Drawings 89 89
- 90 Drawings 90
- Drawings 91 91
- 100K-2GSR Winch MountAssembly 92
- 94 Drawings 94
- Drawings 95 95
- 100K-2GSR Stand Assembly 96
- 98 Drawings 98
- Drawings 99 99
- 100K-2GSR Pipe Stop Assembly 100
- 102 Drawings 102
- Drawings 103 103
- 104 Drawings 104
- Drawings 105 105
- 106 Drawings 106
- Drawings 107 107
- 108 Drawings 108
- VALVE ADJUSTMENT 109
- 110 Drawings 110
- Drawings 111 111
- 112 Drawings 112
- Drawings 113 113
- 114 Drawings 114
- Drawings 115 115
- 116 Drawings 116
- Drawings 117 117
- 118 Drawings 118
- Drawings 119 119
- 120 Drawings 120
- Drawings 121 121
- 25726 Chain Oiler Assembly 122
- 124 Drawings 124
- Drawings 125 125
- 126 Drawings 126
- Drawings 127 127
- 128 Drawings 128
- Drawings 129 129
- 130 Drawings 130
- Drawings 131 131
- 132 Drawings 132
- Drawings 133 133
- 134 Drawings 134
- Drawings 135 135
- 59R Roller Assembly, Winch 136
- 138 Drawings 138
- Drawings 139 139
- 140 Drawings 140
- Drawings 141 141
- A11-LCH Multiplex Connector 142
- A11-RCH Multiplex Connector 144
- 146 Drawings 146
- Drawings 147 147
- 148 Drawings 148
- Drawings 149 149
- H25 Hydraulic Filter Assembly 150
- H37S-2 Push Cylinder Assembly 152
- 154 Drawings 154
- 155Drawings 155
- 156 Drawings 156
- 157Drawings 157
- 100K-2GSR Torque Manifold 158
- 159Drawings 159
- 100K-2GSR Gage Manifold 160
- 161Drawings 161
- 100K-2GSR Winch Assembly 162
- 164 Drawings 164
- HAWK INDUSTRIES, INC 165
- 165Drawings 165
Produits connexes et manuels pour Machines spéciales Hawk-industries Hawkjaw Sr. Manual 100K-2GSR Serial Numbers 101 to
Machines spéciales Hawk-industries Hawkjaw Sr. Manual 100K-2GSR Serial Numbers 121 to Manuel d'utilisateur
(192 pages)
(192 pages)
Machines spéciales Hawk-industries Hawkjaw Sr. 100K-2GSR M100K Serial Numbers 141 to Manuel d'utilisateur
(215 pages)
(215 pages)
Machines spéciales Hawk-industries Hawkjaw Sr. Manual M100K-2GSR Serial Numbers 201 t Manuel d'utilisateur
(215 pages)
(215 pages)
Machines spéciales Hawk-industries Spinner Manual 550 HYDRAULIC Serial Numbers 206 to Manuel d'utilisateur
(101 pages)
(101 pages)
Machines spéciales Hawk-industries Spinner Manual 950 HYDRAULIC Serial Numbers 401 to Manuel d'utilisateur
(101 pages)
(101 pages)
Machines spéciales Hawk-industries Spinner Manual 550 PNEUMATIC Serial Numbers 106 to Manuel d'utilisateur
(101 pages)
(101 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.670 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels