Hawk-industries Hawkjaw Sr. Manual 100K-2GSR Serial Numbers 121 to Manuel d'utilisateur Page 40
- Page / 192
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Maintenance & Repair 39
Changing the Heel Dies
Changing the Heel Dies
Initial Steps
1. Make sure the HawkJaw is off
the drill pipe connection and in
the rest position on the derrick.
2. Shut down the Hydraulic power
unit.
3. Press the Grip button
repeatedly to bleed hydraulic
pressure.
4. Disconnect the Air power
supply.
5. Push in the “E” stop.
6. Assume that there is still a load
on every actuator. Proceed with
caution.
Middle Wrench Heel Die
1. Use the 3/4" wrench to remove
the Heel Die Roller Bolts (B).
2. Pull out the Heel Die Pin (P).
3. Remove the Top Die Retainer (DR).
4. Slide out the worn Die (D).
5. Make sure the back and sides of
the new Die are clean.
6. Grease the back of the new Die.
7. Insert the new Die into the Die
Holder (DH) with the teeth of the
Die facing out.
Continued on next page...
P B
DR
DH D
- OPERATION, MAINTENANCE 1
- SERVICE MANUAL 1
- 100K-2GSR Serial # -141 1
- M100K Serial # 200 1
- Introduction 2
- Table of Contents 3
- Warranty 7
- Specification Sheet 8
- Ordering Instructions 9
- HawkJaw Location 10
- Hanging Cable Location 10
- Hanging Cable Requirements 11
- Hydraulic Requirements 12
- Air Requirements 13
- Raise/Lower Cylinder Hook-Up 14
- Winch Hook-Up 15
- Start-Up Procedure 18
- Adjust for Make Up 19
- Position for Make Up 21
- Position for Make Up (cont.) 22
- Setting Make Up Torque 23
- Make UpMake Up 24
- Low Torque Warning Test 25
- Adjust for Break Out 26
- Position for Break Out 28
- Break Out 30
- Wrench Maintenance 31
- Filter Maintenance 35
- Changing the Hook Dies 37
- Changing the Heel Dies 38
- Spinner Maintenance 44
- Changing the Spinner Chain 49
- Changing the Driver Rollers 51
- Part Numbers 54
- Changing the Torque Cylinder 55
- Changing the Grip Cylinder 59
- Trouble Shooting 68
- 78 Drawings 79
- Drawings 79 80
- 80 Drawings 81
- Drawings 81 82
- Drawings 83 84
- 84 Drawings 85
- Drawings 85 86
- 100K-2GSR Hanger Assembly 87
- 88 Drawings 89
- Drawings 89 90
- 90 Drawings 91
- Drawings 91 92
- 92 Drawings 93
- Drawings 93 94
- 94 Drawings 95
- Drawings 95 96
- 100K-2GSR Stand Assembly 97
- 98 Drawings 99
- Drawings 99 100
- 100K-2GSR Pipe Stop Assembly 101
- 102 Drawings 103
- Drawings 103 104
- 104 Drawings 105
- Drawings 105 106
- 106 Drawings 107
- Drawings 107 108
- 108 Drawings 109
- Drawings 109 110
- 110 Drawings 111
- Drawings 111 112
- LEFT CONNECTOR 112
- RIGHT CONNECTOR 112
- 112 Drawings 113
- Drawings 113 114
- 114 Drawings 115
- Drawings 115 116
- 116 Drawings 117
- Drawings 117 118
- 118 Drawings 119
- Drawings 119 120
- 120 Drawings 121
- Drawings 121 122
- 25726 Chain Oiler Assembly 123
- 124 Drawings 125
- Drawings 125 126
- 126 Drawings 127
- Drawings 127 128
- 128 Drawings 129
- Drawings 129 130
- 130 Drawings 131
- Drawings 131 132
- 132 Drawings 133
- Drawings 133 134
- 134 Drawings 135
- Drawings 135 136
- 59R Roller Assembly, Winch 137
- 138 Drawings 139
- Drawings 139 140
- 140 Drawings 141
- Drawings 141 142
- A11-LCH Multiplex Connector 143
- A11-RCH Multiplex Connector 145
- 146 Drawings 147
- Drawings 147 148
- 148 Drawings 149
- Drawings 149 150
- H25 Hydraulic Filter Assembly 151
- H37S-2 Push Cylinder Assembly 153
- 154 Drawings 155
- Drawings 155 156
- 156 Drawings 157
- Drawings 157 158
- 100K-2GSR Torque Manifold 159
- 100K-2GSR Gage Manifold 161
- 100K-2GSR Winch Assembly 163
- 031-24625 Reducer Gear Box 165
- 166 Drawings 167
- Drawings 167 168
- 168 Drawings 169
- Drawings 169 170
- 170 Drawings 171
- Drawings 171 172
- 0.+$1*(5$66(0%/< 173
- 174 Drawings 175
- Drawings 175 176
- 176 Drawings 177
- Drawings 177 178
- 178 Drawings 179
- Drawings 179 180
- 180 Drawings 181
- 7% 183
- 723%27720 183
- 723 185
- 723 185
- 723 186
- 723 186
- 186 Drawings 187
- Drawings 187 188
- 188 Drawings 189
- NotesNotes 191
- Maintenance Schedule 192
Produits connexes et manuels pour Machines spéciales Hawk-industries Hawkjaw Sr. Manual 100K-2GSR Serial Numbers 121 to
Machines spéciales Hawk-industries Hawkjaw Sr. 100K-2GSR M100K Serial Numbers 141 to Manuel d'utilisateur
(215 pages)
(215 pages)
Machines spéciales Hawk-industries Hawkjaw Sr. Manual M100K-2GSR Serial Numbers 201 t Manuel d'utilisateur
(215 pages)
(215 pages)
Machines spéciales Hawk-industries Spinner Manual 550 HYDRAULIC Serial Numbers 206 to Manuel d'utilisateur
(101 pages)
(101 pages)
Machines spéciales Hawk-industries Spinner Manual 950 HYDRAULIC Serial Numbers 401 to Manuel d'utilisateur
(101 pages)
(101 pages)
Machines spéciales Hawk-industries Spinner Manual 550 PNEUMATIC Serial Numbers 106 to Manuel d'utilisateur
(101 pages)
(101 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.201 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels