Hawk-industries Hawkjaw Jr. Manual 65K-ALS Serial Numbers 4 to 9 Manuel d'utilisateur Page 82
- Page / 139
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Trouble Shooting
Symptom Remedy
l The Drive motor is worn out. With filtered
hydraulic fluid through a Hawk approved filter, the
Drive motor is a long term wear item. If all
other rotating members on the spinner work,
inspect the rotating group, bearings and seals for
wear. Replace where necessary. See Drawings, p.
134.
l The filter element is clogged. Replace the filter
element. See Maintenance & Repair, p. 35.
Check the lead-in pressure and tank lines for any
obstructions. Also check the quick disconnects
to see that they are securely tightened. A bad
quick disconnect can cause the Hawkjaw to mal-
function. Replace the faulty connector.
l The air pressure is low. Increase the air pressure
to the HawkJaw to at least 100 psi.
l The hydraulic pressure is low. Increase the
hydraulic pressure.
Do not increase the pressure over 2600 psi, or the
hydraulic fluid will pass over the relief valve and
heat up the hydraulic fluid. This will cause damage
to the HawkJaw and to the pump, and will severely
shorten component life.
l Check to make sure the hydraulic power unit is
producing 2600 psi at 20-35 gpm.
l Check to make sure the hydraulic power unit
pressure compensa-
tor setting is at 2600 psi.
l There is a leak in the hydraulic system. Check for
any visual leaks in the hoses, fittings, manifolds,
cylinder rod heads, or cylinder rod wiper seals.
Replace necessary components. See Drawings, p.
114, 94, 96, 98, 100.
l There is a leak in the hydraulic system. Operate
the HawkJaw. Feel the outside of all actuators. If
a portion of the cylinder surface is too hot to leave
your hand on the cylinder, the leak is inside the
cylinder. Replace the cylinder seals. If necessary,
Spinner performance and speed
not up to par, or spinner doors
close on the drill pipe tube, but
the pipe does not rotate down to
the drill pipe connection
shoulder. ( Cont.)
HawkJaw performance and
speed not up to par.
HawkJaw
Performance
82 Troubleshooting
Continued on next page.
- OPERATION, MAINTENANCE AND 1
- SERVICE MANUAL 1
- MODEL 65K-ALS 1
- Introduction 2
- Table of Contents 3
- Table of Contents (cont.) 4
- Warranty 6
- Specification Sheet 7
- Ordering Instructions 8
- Hanging Cable Location 9
- HawkJaw Location 9
- Hanging Cable Requirements 10
- Hydraulic Requirements 11
- Air Requirements 12
- Installation 13
- Start-up Procedure 14
- Adjust for Make Up 15
- Part Name Part # 18
- Shift Spinner for Make Up 19
- Position for Make Up 20
- Position for Make Up (cont.) 21
- Setting Make Up Torque 22
- Shown set for 30,000 ft. lbs 23
- LOW TORQUE WARNING SYSTEM 23
- Adjust for Break Out 24
- Operation 27
- Shift Spinner for Break Out 28
- Position for Break Out 29
- Turnbuckle (TB) 061-3022T55 30
- Break Out 31
- Operation32 32
- Wrench Maintenance 33
- Hydraulic Filter Maintenance 37
- Air Filter Maintenance 38
- Changing the Hook Dies 39
- Changing the Heel Dies 40
- Maintenance 41
- & Repair 41
- Middle Wrench Heel Die 42
- Bottom Wrench Heel Die 44
- Spinner Maintenance 46
- Changing the Spinner Chain 50
- Changing the Drive Rollers 52
- Changing the Torque Cylinder 56
- BB BCP BE 59
- Torque Cylinder Seals 60
- Changing the Grip Cylinders 61
- Grip Cylinder Seals 62
- Trouble Shooting 69
- Low Wear Parts 88
- Middle Wrench 90
- Pipe Stop Assembly 92
- 94 Drawings 94
- Torque Cylinder 96
- Grip Cylinder 98
- Spinner Grip Cylinder 100
- Raise/Lower Cylinder 102
- 104 Drawings 104
- Drawings 105
- 106 Drawings 106
- 108 Drawings 108
- Air Pilot Assembly 110
- 112 Drawings 112
- 114 Drawings 114
- Hydraulic Fittings and Hoses 116
- Left Control Handle Assembly 118
- Right Control Handle Assembly 120
- Left Conduit Assembly 122
- Right Conduit Assembly 124
- Stand Assembly 126
- 128 Drawings 128
- Spinner Manifold 129
- Wear Parts 130
- Hanger Assembly 132
- Reducer Assembly 134
- Spinner Drive Motor Assembly 136
- 138 Drawings 138
Produits connexes et manuels pour Machines spéciales Hawk-industries Hawkjaw Jr. Manual 65K-ALS Serial Numbers 4 to 9
Machines spéciales Hawk-industries Hawkjaw Jr. Manual 65K-2GJR Serial Numbers 10 to 2 Manuel d'utilisateur
(151 pages)
(151 pages)
Machines spéciales Hawk-industries Hawkjaw Jr. Manual 65K-2GJR Serial Numbers 21 to 3 Manuel d'utilisateur
(147 pages)
(147 pages)
Machines spéciales Hawk-industries Hawkjaw Sr. Manual ALS Serial Numbers 1 to 100 Manuel d'utilisateur
(159 pages)
(159 pages)
Machines spéciales Hawk-industries Hawkjaw Sr. Manual 100K-2GSR Serial Numbers 101 to Manuel d'utilisateur
(165 pages)
(165 pages)
Machines spéciales Hawk-industries Hawkjaw Sr. Manual 100K-2GSR Serial Numbers 121 to Manuel d'utilisateur
(192 pages)
(192 pages)
Machines spéciales Hawk-industries Hawkjaw Sr. 100K-2GSR M100K Serial Numbers 141 to Manuel d'utilisateur
(215 pages)
(215 pages)
Machines spéciales Hawk-industries Hawkjaw Sr. Manual M100K-2GSR Serial Numbers 201 t Manuel d'utilisateur
(215 pages)
(215 pages)
Machines spéciales Hawk-industries Spinner Manual 550 HYDRAULIC Serial Numbers 206 to Manuel d'utilisateur
(101 pages)
(101 pages)
Machines spéciales Hawk-industries Spinner Manual 950 HYDRAULIC Serial Numbers 401 to Manuel d'utilisateur
(101 pages)
(101 pages)
Machines spéciales Hawk-industries Spinner Manual 550 PNEUMATIC Serial Numbers 106 to Manuel d'utilisateur
(101 pages)
(101 pages)
Helio manuels
La liste des produits de Helio contient 4 les manuels et guides d'utilisation des modèles 4 dans les appareils de type 4
Commentaires sur ces manuels