Hawk-industries Hawkjaw Jr. Manual 65K-ALS Serial Numbers 4 to 9 Manuel d'utilisateur Page 64
- Page / 139
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Changing the Grip Cylinders (cont.)
7. Remove the 3 bolts (B) that
mount the grip cylinder Clevis
Plate (CP). Then remove the
Hook Clevis Plate (CP).
10. Pull out the Middle Grip
Cylinder Cap side Pin (MCP).
11. Slide out the Middle Grip Cylin-
der (MC).
12. Use the Two 11/16" wrenches to
slowly loosen the Rod side Hose
(RH). Check for fluid flow.
Bleed any pressure. Disconnect
the Rod side Hose (RH).
13. Use the Two 11/16" wrenches to
slowly loosen the Cap side Hose
(CH). Check for fluid flow.
Bleed any pressure. Disconnect
the Cap side Hose (CH).
14. Replace the Middle Grip
Cylinder (MC).
15. Use the Two 11/16" wrenches to
connect the Cap side Hose (CH).
16. Use the Two 11/16" wrenches to
connect the Rod side Hose (RH).
17. With the Middle Grip Cylinder in
place, replace the Clevis Plate
(CP). Be sure the rod on the
Hook Clevis Plate assembly goes
through the eye on the cylinder
rod.
18. Replace the 3 bolts (B) in the
Hook Clevis Plate (CP).
20. Insert the Middle Grip Cylinder
Cap side Pin (MCP).
B
RH
CH
MCP
MC
64 Maintenance & Repair
Continued on next page.
CP
- OPERATION, MAINTENANCE AND 1
- SERVICE MANUAL 1
- MODEL 65K-ALS 1
- Introduction 2
- Table of Contents 3
- Table of Contents (cont.) 4
- Warranty 6
- Specification Sheet 7
- Ordering Instructions 8
- Hanging Cable Location 9
- HawkJaw Location 9
- Hanging Cable Requirements 10
- Hydraulic Requirements 11
- Air Requirements 12
- Installation 13
- Start-up Procedure 14
- Adjust for Make Up 15
- Part Name Part # 18
- Shift Spinner for Make Up 19
- Position for Make Up 20
- Position for Make Up (cont.) 21
- Setting Make Up Torque 22
- Shown set for 30,000 ft. lbs 23
- LOW TORQUE WARNING SYSTEM 23
- Adjust for Break Out 24
- Operation 27
- Shift Spinner for Break Out 28
- Position for Break Out 29
- Turnbuckle (TB) 061-3022T55 30
- Break Out 31
- Operation32 32
- Wrench Maintenance 33
- Hydraulic Filter Maintenance 37
- Air Filter Maintenance 38
- Changing the Hook Dies 39
- Changing the Heel Dies 40
- Maintenance 41
- & Repair 41
- Middle Wrench Heel Die 42
- Bottom Wrench Heel Die 44
- Spinner Maintenance 46
- Changing the Spinner Chain 50
- Changing the Drive Rollers 52
- Changing the Torque Cylinder 56
- BB BCP BE 59
- Torque Cylinder Seals 60
- Changing the Grip Cylinders 61
- Grip Cylinder Seals 62
- Trouble Shooting 69
- Low Wear Parts 88
- Middle Wrench 90
- Pipe Stop Assembly 92
- 94 Drawings 94
- Torque Cylinder 96
- Grip Cylinder 98
- Spinner Grip Cylinder 100
- Raise/Lower Cylinder 102
- 104 Drawings 104
- Drawings 105
- 106 Drawings 106
- 108 Drawings 108
- Air Pilot Assembly 110
- 112 Drawings 112
- 114 Drawings 114
- Hydraulic Fittings and Hoses 116
- Left Control Handle Assembly 118
- Right Control Handle Assembly 120
- Left Conduit Assembly 122
- Right Conduit Assembly 124
- Stand Assembly 126
- 128 Drawings 128
- Spinner Manifold 129
- Wear Parts 130
- Hanger Assembly 132
- Reducer Assembly 134
- Spinner Drive Motor Assembly 136
- 138 Drawings 138
Produits connexes et manuels pour Machines spéciales Hawk-industries Hawkjaw Jr. Manual 65K-ALS Serial Numbers 4 to 9
Machines spéciales Hawk-industries Hawkjaw Jr. Manual 65K-2GJR Serial Numbers 10 to 2 Manuel d'utilisateur
(151 pages)
(151 pages)
Machines spéciales Hawk-industries Hawkjaw Jr. Manual 65K-2GJR Serial Numbers 21 to 3 Manuel d'utilisateur
(147 pages)
(147 pages)
Machines spéciales Hawk-industries Hawkjaw Sr. Manual ALS Serial Numbers 1 to 100 Manuel d'utilisateur
(159 pages)
(159 pages)
Machines spéciales Hawk-industries Hawkjaw Sr. Manual 100K-2GSR Serial Numbers 101 to Manuel d'utilisateur
(165 pages)
(165 pages)
Machines spéciales Hawk-industries Hawkjaw Sr. Manual 100K-2GSR Serial Numbers 121 to Manuel d'utilisateur
(192 pages)
(192 pages)
Machines spéciales Hawk-industries Hawkjaw Sr. 100K-2GSR M100K Serial Numbers 141 to Manuel d'utilisateur
(215 pages)
(215 pages)
Machines spéciales Hawk-industries Hawkjaw Sr. Manual M100K-2GSR Serial Numbers 201 t Manuel d'utilisateur
(215 pages)
(215 pages)
Machines spéciales Hawk-industries Spinner Manual 550 HYDRAULIC Serial Numbers 206 to Manuel d'utilisateur
(101 pages)
(101 pages)
Machines spéciales Hawk-industries Spinner Manual 950 HYDRAULIC Serial Numbers 401 to Manuel d'utilisateur
(101 pages)
(101 pages)
Machines spéciales Hawk-industries Spinner Manual 550 PNEUMATIC Serial Numbers 106 to Manuel d'utilisateur
(101 pages)
(101 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.870 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels